Inficon MPI-16 Crucible Indexer Manual de usuario

OPERATION AND SERVICE MANUALPocket IndexersIPN 614800 Rev. BMPI-16 and MPI-16H

MPI-16 & MPI-16H POCKET INDEXERS General Description 1-1 1 General Description 1.1 Purpose The MPI-16 Pocket Indexer allows for automatic or m

MPI-16 & MPI-16H POCKET INDEXERS 1-2 General Description required, to turn the crucible. The maximum torque generated by each version is

MPI-16 & MPI-16H POCKET INDEXERS General Description 1-3 1.2.8 Noise Immunity The MPI-16 employs numerous electronics techniques (including the

MPI-16 & MPI-16H POCKET INDEXERS 1-4 General Description 1.3 Specifications – MPI-16 Pocket Indexer 1.3.1 Indexing Number of Positions S

MPI-16 & MPI-16H POCKET INDEXERS General Description 1-5 1.3.7 Physical Dimensions [w] × [h] × [d] (including shaft length and protruded switc

MPI-16 & MPI-16H POCKET INDEXERS 1-6 General Description 1.5 Accessories 1.5.1 Remote Panel The Remote Panel is a required system compone

MPI-16 & MPI-16H POCKET INDEXERS Package Contents 2-1 2 Package Contents Carefully inspect your MPI-16 Indexer and its shipping container for ev

MPI-16 & MPI-16H POCKET INDEXERS Setup and Installation 3-1 3 Setup and Installation 3.1 Introduction The MPI-16 Pocket Indexer is capable of

MPI-16 & MPI-16H POCKET INDEXERS 3-2 Setup and Installation Because it can be changed during normal operation, Speed Select is not con

MPI-16 & MPI-16H POCKET INDEXERS Setup and Installation 3-3 3.3.1 Number of Positions This setting indicates how many positions the MPI-16 can

MPI-16 & MPI-16H POCKET INDEXERS 3-4 Setup and Installation 3.3.3 Banana Pocket #2 Start Position This setting indicates the position num

MPI-16 & MPI-16H POCKET INDEXERS Setup and Installation 3-5 3.4 Configuration Examples These examples illustrate a few examples of crucible set

MPI-16 & MPI-16H POCKET INDEXERS 3-6 Setup and Installation Figure 3-4 Configuration Example - 8-Position Crucibles 3.4.1 Configuration

MPI-16 & MPI-16H POCKET INDEXERS Setup and Installation 3-7 1 Blink – Switch Out Of Range Error

MPI-16 & MPI-16H POCKET INDEXERS 3-8 Setup and Installation 3.5 Installation in Your System After successfully configuring the MPI-16, it

MPI-16 & MPI-16H POCKET INDEXERS Setup and Installation 3-9 Figure 3-5 MPI-16 Outline Dimensions

MPI-16 & MPI-16H POCKET INDEXERS 3-10 Setup and Installation Figure 3-6 Typical Mounting 1” ROTARY MOTION FEEDTHROUGH (NOT SUPPLIED) VACUUM B

MPI-16 & MPI-16H POCKET INDEXERS Setup and Installation 3-11 3.6 System Connections On the rear side of the MPI-16, there are two connectors pro

MPI-16 and MPI-16HResearch Quartz Crystal MicrobalanceOPERATION AND SERVICE MANUALIPN 614800 Rev. Bwww.inficon.com [email protected] to our c

MPI-16 & MPI-16H POCKET INDEXERS 3-12 Setup and Installation If you have purchased a INFICON’s MDC-360 Thin Film Controller with your MPI

MPI-16 & MPI-16H POCKET INDEXERS Setup and Installation 3-13 Figure 3-7 System Connections

MPI-16 & MPI-16H POCKET INDEXERS 3-14 Setup and Installation 3.7 Connecting to the Remote Panel If you plan on controlling the MPI-16 manual

MPI-16 & MPI-16H POCKET INDEXERS Setup and Installation 3-15 Figure 3-9 Remote Panel - Rear View

MPI-16 & MPI-16H POCKET INDEXERS 3-16 Setup and Installation Figure 3-10 Pocket Indexer Rear View

MPI-16 & MPI-16H POCKET INDEXERS Operation 4-1 4 Operation Regardless of whether you will be running the MPI-16 in Manual or Automatic mod

MPI-16 & MPI-16H POCKET INDEXERS 4-2 Operation addition to a Deposition Controller allows the operator to run a program, pause the program

MPI-16 & MPI-16H POCKET INDEXERS Operation 4-31 0 1 1 12 1 1 0 0 13 1 1 0 1 14 1 1 1 0 15 1 1 1 1 16 Table 4-1 Pocket Select Inputs T

MPI-16 & MPI-16H POCKET INDEXERS 4-4 Operation Table 4-2 Pocket Position Feedback Outputs Truth Table 4.2.3 Remote Selection of Rotation

MPI-16 & MPI-16H POCKET INDEXERS Operation 4-5switch located on the MPI-16 to Remote, indicating you will be controlling the speed remotel

TrademarksThe trademarks of the products mentioned in this manual are held by the companies that produce them.INFICON® is a trademark of INFICON Inc.A

MPI-16 & MPI-16H POCKET INDEXERS 4-6 Operation 8. Set the Drive parameter to either “Up,” “Down,” or “Fast.” (Fast mode will turn the cr

MPI-16 & MPI-16H POCKET INDEXERS Operation 4-7 Figure 4-1 DSUB-25 Female to DSUB-37 Female Cable Diagram

MPI-16 & MPI-16H POCKET INDEXERS 4-8 Operation 4.3 System Faults Several events may occur to the MPI-16 during operation that will cause a

MPI-16 & MPI-16H POCKET INDEXERS Operation 4-9 4 Blinks – Jam Fault

MPI-16 & MPI-16H POCKET INDEXERS 4-10 Operation 8 Blinks – Firmware Fault

MPI-16 & MPI-16H POCKET INDEXERS Operation 4-114.4 Abort and Reset The MPI-16 has a multi-purpose Abort/Reset switch on its main panel.

MPI-16 & MPI-16H POCKET INDEXERS Troubleshooting Aids 5-15 Troubleshooting Aids The MPI-16 was designed around a philosophy of trouble-free an

MPI-16 & MPI-16H POCKET INDEXERS Troubleshooting Aids 5-2 Fault LED is blinking. Various. Count the numbers of blinks, then refer to Table 4-

MPI-16 & MPI-16H POCKET INDEXERS Appendix A 6-1 6 Appendix A Quick Reference for Configuration Errors and Faults The following guide will give

INFICON warrants the product to be free of functional defects in material and workmanship and that it will perform in accordance with its published sp

MPI-16 & MPI-16H POCKET INDEXERS Table of Contents 1 General Description...

MPI-16 & MPI-16H POCKET INDEXERS 3.6 System Connections......

MPI-16 & MPI-16H POCKET INDEXERS Table of Figures FIGURE 3-1 POCKET INDEXER FRONT VIEW..............